Searching...
Shop Online Sign Up for Our Email Newsletter! Contact Us Facebook Twitter YouTube Pinterest Instagram
Village Cycle Center - Chicago's Bike Experts

1337 N Wells St. Chicago, IL
312-751-2488
Mon - Fri 10am - 8pm
Sat & Sun 10am - 5pm 

Have a Question? Get an Answer. Email Us!
 
 
 
 
 
 
 

Bicycle Lubrication

Bicycles are made up of many parts that work best and last longest when properly lubed. View this diagram to see the lube points for modern bicycles. Below, we explain what's involved.

Lubricants & Grease

The lubricant used the most is a liquid lube, which we sell in small drip and spray containers. We recommend purchasing our cycling-specific lubes because they're perfectly formulated for your two-wheeler. This matters because the typical all-around lubes sold at hardware stores are often too thick or too thin to lubricate your bike properly. And, they'll usually leave an oily residue that can make a mess of your machine and clothing. Also, some products will attack the seals on bike components damaging your equipment.

Liquid lubes come in a wide and sometimes confusing variety. We can recommend one perfect for your bike and our riding conditions. You only need a small container and it'll last for many rides.

Depending on how much you plan to work on your bike, you may want to pick up some grease, too. This is a thicker lube, about the consistency of Crisco shortening. We sell it in squeeze tubes.

You can't see it, but grease is what's inside the headset (steering mechanism), hubs, bottom bracket and pedals. There are bearings inside these components and they sit in a bed of grease that keeps them lubed and turning freely.

Because grease is thick and these systems are protected from the elements, it's unlikely you'll need to work on these parts. However, grease is also used to lubricate threads and parts that fit together, such as the seatpost and stem and the associated bolts. If you plan to work on these parts, it's good to have some grease on hand.

Lubing It Part By Part

How often you lube your bike depends on how you use it. Ideally, the moving parts will always be lightly lubed. A dry, squeaking bike needs lube. A bike covered with grime means you're using too much lube (or the wrong lube).

Applying lube is just a matter of dripping or spraying some on, operating the part to get the lube down inside, letting it sit for a bit for the lube to fully penetrate and then wiping off the excess.

Chain: lubricate the lower run of links (see diagram) as you pedal backwards with your hand until you've lightly coated the entire chain.


Brakes: lube the pivot points where the brake parts move against each other. If there's a quick-release mechanism and/or adjustment barrel (sometimes on the brake lever; see diagram), lightly lube these, too (on the threads for the adjustment barrel). Do NOT get lube on the brake pads or rims!

Derailleurs: wet the pivot points on the derailleur bodies. And, for the rear, while the bike's resting on its side, apply a little to the center of the derailleur pulleys. Lube the adjustment barrel, too.

Clipless pedals: apply lube if your shoes and pedals are creaking when you ride and/or it's difficult to get in or out. Remember to remove your shoes before walking into the house so you don't leave oily footprints across the carpet! 

Cables: most brake and shift cables don't require lube because they're inside nylon-lined housing. If yours bind, however, you can add lube if your bike has split housing stops. These allow accessing the cables and lubing. It's done by opening the brake quick release to create slack and then pulling slightly to free the housing from the frame stops. You can then slide the housing to get at the cable inside. For derailleurs, shift onto the largest cog or ring and then move the levers back without pedaling. This creates enough slack to get the housing out of the stops and lube the shift cables (if necessary, don't forget to lube where the cables pass beneath the bottom bracket, too).

Suspension fork: double-check that your lube won't harm nylon or rubber seals. If it's safe, you can apply a few drops to the upper fork legs and push down on your handlebars a few times to compress the fork and work the lube past the seals. This will keep the fork's action smooth.

Lubricants / Cleaners

Finish Line No Drip Chain Luber
$8.99

Lubing your bicycle's chain is an essential but messy task. But now,… [more]

Finish Line Dry Lubricant With Teflon (2-Ounce Bottle)
$4.99

Finish Line's Dry Lubricant With Teflon keeps your bike running… [more]

Product Rating
 
5.0 stars
 (2 Reviews)
White Lightning Clean Ride
$8.99 - $11.99

White Lightning's Clean Ride is the same legendary self-cleaning lube… [more]

Finish Line E-Shift Groupset Cleaner (16-Ounce Spray)
$14.99

Finish Line's E-Shift Groupset Cleaner is specially formulated to keep… [more]

Park Tool Synthetic-Blend Chain Lube
$8.49

Keep your chain running smoothly with Park's Synthetic-Blend Chain Lube.… [more]

Finish Line Ecotech Degreaser
$9.99 - $13.99

- A biodegradable degreaser that cuts through the toughest grime - Strong… [more]

 
Follow Us on FacebookFollow Us on TwitterCheck us out on YoutubeFollow Us on PinterestFollow Us on InstagramHave a question? Get an answer. EMAIL US.
Email Icon
Village Cycle Center
1337 N WELLS ST
Chicago, IL 60610
(312) 751-2488
HOURS
MON-FRI 10 - 8
SAT - SUN 10 - 5
Shop Bicycles
All Bikes
Road Bikes
Mountain Bikes
Cyclocross Bikes
Commuter Bikes
Comfort Bikes
Fitness Bikes
Hybrid Bikes
Kids’ Bikes
Women's Bikes
Shop Cycling Gear
Cycling Gloves
Cycling Jerseys
Cycling Shorts & Bibs
Cycling Shoes
Bike Helmets
Bike Lights
Bike Locks
Bike Pumps
Bike Tires & Tubes
Car Racks
Quick Links
Bike Repair
Bike Fit
Trek Financing
Now Hiring
Village Cycle Blog
Share Your Feedback
Shipping Policies
Site Map
Your Privacy
Contact Us